Elaskon Polymer Dunkel
[:en]
Elaskon Polymer Dunkel
Elaskon MS Polymer dunkel is a sprayable seam seal for car body, ventilation and air conditioning, metal construction, etc.
Characteristics:
Elaskon MS Polymer dunkel is elastic, good moisture, weather and temperature resistant from -40 ° C to + 80 ° C (short-term up to 120 ° C). Good adhesion to wood materials, thermosets (except PE, PP, PTFE) and mineral substrates, on glass, many metals (zinc, aluminum, steel), lacquers and primers. It is elastic, good moisture, weather and temperature resistant from -40 ° C to + 80 ° C (short term up to 120 ° C).
Processing instructions:
Elaskon MS polymer dunkel surfaces must be clean, dry and free of grease. The product can be sprayed with many paints immediately after application (experience up to 2 hours). After some time, adhesion problems may occur with some varnish systems. POP copolymer, one-component, moisture-curing and solvent-based. Screw the cartridge on the thread and screw it into the gun (observe the instructions of the gun manufacturer): The cartridge can be left in the gun until it is completely emptied.
By adjusting directly on the gun, a structural surface as well as two-dimensional coating and profile seam can be produced. There must always be a cartridge in the gun. Never place the gun aside, otherwise the material in the gun will dry out. Do not mix with non-cured PU material. Liability and compatibility with plastics and lacquers must be checked for specific properties.
Looking for any other schmierstoffe product in ELASKON Lubrication or other Lubricant ? Just give us a call.[:de]
Elaskon Polymer Dunkel
Elaskon MS Polymer dunkel ist eine sprühbare Nahtabdichtung für den Karosserie-, Lüftungs- und Klimatechnik, Metallbau, etc.
Eigenschaften:
Elaskon MS Polymer dunkel ist elastisch, gut feuchtigkeits-, witterungs- und temperaturbeständig von –40°C bis +80°C (kurzfristig bis 120°C). Gute Haftung auf Holzwerkstoffen, Duro- und Thermoplasten (außer PE, PP, PTFE) und mineralischen Untergründen, auf Glas, vielen Metallen (Zink, Aluminium, Stahl), Lacken und Grundierungen. Es ist elastisch, gut feuchtigkeits-, witterungs- und temperaturbeständig von –40°C bis +80°C (kurzfristig bis120°C).
Verarbeitungshinweise:
Elaskon MS Polymer dunkel Flächen müssen sauber, trocken und fettfrei sein. Das Produkt ist mit vielen Lacken sofort nach der Applikation überspritzbar (erfahrungsgemäß bis zu 2 Stunden). Nach längerer Zeit können Haftungsprobleme mit einigen Lacksystemen auftreten. POP-Mischpolymer einkomponentig, durch Luftfeuchtigkeit härtend und lösungsmittelhaltig. Kartusche am Gewinde aufschneiden und in die Pistole einschrauben (Anleitung des Pistolenherstellers beachten): Kartusche kann bis zur völligen Entleerung in der Pistole belassen werden.
Durch Einstellung direkt an der Pistole kann sowohl eine Strukturnaht als auch flächige Beschichtung und Profilnaht erzeugt werden. Es muß sich immer eine Kartusche in der Pistole befinden. Niemals Pistole leer zur Seite legen, da sonst das Material in der Pistole austrocknet. Nicht mit noch nicht ausgehärtetem PU-Material in Verbindung bringen. Haftung und Verträglichkeit mit Kunststoffen und Lacken muß objektbezogen geprüft werden.
[:]